Factory Free sample Foam Dispenser - Semi-Automatic Round Bottle Labeling Machine – Maxwell
Factory Free sample Foam Dispenser - Semi-Automatic Round Bottle Labeling Machine – Maxwell Detail:
The machine adopts high precision intelligent electric eye combined with extremely reliable PLC controlling division labels into lots and labeling. By adsorbing adhesive stickers into the labeling head with air pressure, the labeling can be realized.
B.Advantages of product
1，Efficiency is up to 50 times/minutes.
2，Labeling bottle adjustable, meet different before and after the workpiece labeling needs.
3，Excellent effect can be delivered for labels with no wrinkles and no bubbles
4，Choose brand PLC and sensor etc electronic components, performance very stable.
5，Modular design, convenient maintenance and low repair cost..
1，efficiency：≤50pcs/min （according to overall size of the label ）
3，Applicable bottles of diameter：Φ10-130mm
4，label roll：external diameter 300mm inner diameter：75mm
5，Label size：width 8-150mm length 15-210mm
6，Power supply：220 V, 50HZ 120W
1，First install 2 slices of organic glass tray, respectively in two round installation fixed block, and then you will take slot first set of fixed block tray core shaft, pull the green o-rings into fixed block, then fix block with screws.
2，Label installation: the installation rolls label, is direction in clockwise tag along the label, and put the label on the tray to carry the external fixation and lock screw.
3，Thread the labels like the demostration graph below, clockwise around the label head of standard, the bottom standard core clamping device and head out label, the clamp the clamping DaoBiao cylinder lock, otherwise the machine will not work. After threading the whole label across the inner circle, adjust each positioning circle on film guide rolls properly, to ensure exact guide position the tags are in.
Machine diagram & Label stretching chart
|1||positioning arm||2||positioning roll|
|3||stripping plate||4||arm pressure bottle|
|5||rubber roller||6||rubber roller label balance|
|7||magic eye||8||start switch|
|11||organic glass tray||12||tray pivot|
|13||Motor start capacitance||14||amplifier|
|17||Power switch||18||label signals - Reset switch|
|19||Relay||20||label signal generator|
|21||Power transformer||22||waste paper clamping device|
|23||waste paper receiver||24||brake motors|
|25||clamping label guide wheel||26||paper feed adjustment screw|
4，The power supply plugged into the single-phase power supply (requires a good ground connection).
5，The power supply switched on, adjust the magic eye:
Tag magic eye is by amplifier and U fiber-optic first two parts，As shown in Figure：
First will U fiber-optic lines of the head of arbitrary insert fiber socket 2 centimeters, Then lock，Will regulator counterclockwise transferred to the lowest position, The tag through u-shaped fiber u-shaped slot, Two pieces of the label on fiber position of interval between head, Then the clockwise turn the regulator, Rotating slowly from low to high, Until light so far，
Back-and-forth pull Label, Label when on optical fiber head，indicator light off，Again, that signals a stable fine-tuning. These steps are completed, already successful commissioning that label magic eye. General before they have been tested.
a、 Magic eye position：Magic eye position is related to label stopped position, so stay to adjust its position. Different sizes of label the required position is different also, Magic eye if position too back, Will appear label is too long,Cause label head cannot adsorption label. Magic eye position quite rely on ahead, Will appear tags too short, Cause tags do not have labeling.
b、 label stopped position：Is the index sign in labeling strip out before the length of Stripper plate，By magic eye to control. General adjustment to label head traps by tags just can.
6，Adjust the position of positioning arm：Positioning the bottle on the shelf is positioned to play on the rubber roller can rotate the role of, Depending on the diameter of the bottle, to adjust for the location of the bottle.
7，Pressing down the arm pressure bottle, Press to start switch to work, Pressure on the arm of the pressure bottle bottle bottle pressing rubber wheel will rotate week，While rotating the bottle labels adsorbed on the bottle body.
8，If the gaps between the two labels in the position of the magic eye just stop, please click the reset switch, label move, stop in the middle of the label position, so as to ensure the normal signal tags.
1. Abnormal Labeling action：Check the label position is normal，Transmission mechanism have labels or foreign bodies stuck.
2. Label head doesn’t fall or rise：Check whether power source is normal and stable.
3. Labels are adsorbed：Check whether air source is normal and stable.
4. Labels rolled up：Check whether the blowing tube correctly positioned.
5. Waste paper receiver doesn’t pull：Check whether the state tension membrane is too tight.
Product detail pictures:
Related Product Guide:
With a positive and progressive attitude to customer's interest, our enterprise continually improves our products excellent to meet the wants of customers and further focuses on safety, reliability, environmental requirements, and innovation of Factory Free sample Foam Dispenser - Semi-Automatic Round Bottle Labeling Machine – Maxwell , The product will supply to all over the world, such as: Qatar, Hungary, London, With the growing of the company, now our products sold and served at more than 15 countries around the world,such as Europe,North America,Middle-east,South America,Southern Asia and so on. As we bear in our mind that innovation is essential to our growth, new product development is constantly.Besides, Our flexible and efficient operation strategies,High quality products and competitive prices are exactly what our customers are looking for. Also a considerable service brings us good credit reputation.
By Victor Yanushkevich from Las Vegas - 2017.06.29 18:55
Good quality and fast delivery, it's very nice. Some products have a little bit problem, but the supplier replaced timely, overall, we are satisfied.
By Jerry from Vancouver - 2018.05.13 17:00